Majestic Appliances AD MJ 9050 V Wartungshandbuch

BRAND:Majestic SERVICE MANUAL LAUNDRY PRODUCTS Combo Washer Dryer MODELS Service Manual 

10 regulator and the wire M1 on the motor connector, if there is no continuity, the wash timer is bad, check the continuity between terminals 3 &am

11 3) Clothes hot and damp at the end of dry cycle a) Blocked filter / Coin Trap: Remove, clean, and replace filter. b) *No cold water supply: Col

12 Replacement Procedure, Wiring & Testing of Parts 1) Power Switch (52799) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top p

13 2) Door Switch / Door Lock (00750) Replacement Procedure: ▪ Unplug the unit. ▪ Open the door remove the clamp to the door gasket in the fr

14 3) Pressure Switch (50774) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Unfix t

15 4) Cold water valve (10820) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Unfix t

16 5) Hot water valve (00821) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Unfix

17 6) Wash Timer (50819) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Pull out the s

18 7) Dry Timer (50728) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Pull out the so

19 8) Half Load Switch (51799) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Pull ou

2 # TABLE OF CONTENTS # • Warranty Information………………………….……….………………….. 3 • Safe Servicing Practices……………………………………………………… 4 • Inst

20 9) Half Heat Switch (50799) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Pull out

21 10) Fusible Link / Wire with fuse (00807) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide bac

22 11) Thermostat (00808) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ The fusible l

23 12) Fan Motor (50732) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ The fan motor

24 13) Blower / Fan / Impeller Assembly (51733) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide

25 14) Heating Element (00745) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ The he

26 15) Speed Regulator (00791) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ The speed

27 16) Drain Pump (00776) Replacement Procedure: ▪ Unplug the unit. ▪ Make sure that there is no water in the unit. ▪ Carefully pull out the k

28 17) Main Motor (50751) Replacement Procedure: ▪ Unplug the unit. ▪ Make sure that there is no water in the unit. ▪ Remove the back panel (3

29 Quick Check After replacing any part in the unit you can do a quick check to make sure that the unit is working normal by following the procedu

3 WARRANTY INFORMATION FULL ONE-YEAR WARRANTY Equator Advanced Appliances undertakes to the consumer-owner to repair or, at Equator Advanced Applianc

4 SAFE SERVICING PRACTICES To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be obser

5 INSTALLATION: Inlet Hoses The inlet hoses must be fitted with the special rubber washers. These rubber washers ensure a water tight seal between t

6 IMPORTANT PRESERVICE INSTRUCTIONS ► It is advisable for anyone to go through the following points before one actually works

7 DIAGNOSIS AND TECHNICAL TROUBLESHOOTING ◊ INSTALLATION ◊ 1) Machine vibrating or vibrating noise a) Shipping bolts not removed: There are 3 ship

8 is present, the machine should fill. If not, the valve is defective. 2) Unit fills, won’t agitate / tumble a) Belt: Check belt, adjust tension

9 b) Unstable floor: Remove carpeting, move to another location, or install underlayment. c) Unit not leveled properly: Adjust leveling legs, tight